AirLive IP-200PHD-24 User Manual Download Page 84

Page: 84 / 97

5. Troubleshooting & FAQ

AirLive IP-200PHD-24/IP-200PHD-24B

User’s Manual

Enter valid ports in the

Virtual Server

section of your router. Please make sure to

check the box on this line to enable settings. Then the device can be access from

WAN by the router’s WAN IP Address.

By now, you have finished your entire PC configuration for this device.

5.6 DDNS

1. Preface

If you have a

Cable modem or xDSL, this is a great way to host your own Networked

Device

or other TCP/IP Service. Get your own domain like www.yourname.com,

www.yourname.com.tw etc. (Note: This domain must be registered with Internic via

registration authorities such as Network Solutions, DirectNIC, Register.com etc). Your

domain name's dynamic IP address is automatically tracked by a DDNS server.

Summary of Contents for IP-200PHD-24


































































































Search results

Summary of Contents for IP-200PHD-24

Reviews:

Related manuals for IP-200PHD-24

Brands by name

Popular brands

AirLive IP-200PHD-24, User Manual

Search results

Summary of Contents for IP-200PHD-24

Reviews:

Related manuals for IP-200PHD-24

Brands by name

Popular brands