AIRLESSCO 1110E, Service & Operation Manual

Page: 15 / 36

TIP SELECTION GUIDE
SPRAY TIP REPLACEMENT PATTERN WIDTH
SPRAY TIP SELECTION
Thickness of the paint coat per stroke is determined by
spray tip "fan width", rate of the spray gun movement, and
distance to surface.
Two tips having the same tip size, but different pattern
widths will deliver the same amount of paint over a dif-
ferent area (wider or narrower strip).
A spray tip with a narrow pattern width makes it easy to
spray in tight places.
During use, especially with latex paint, high pressure
will cause the orifice to grow larger. This destroys the
pattern.
Replace tips before they become excessively worn.
Worn tips waste paint, cause overspray, make cutting-
in difficult, and decreases sprayer performance.
Spray tip size is based on how many gallons of paint
per minute can be sprayed through the tip. Do not use
a tip larger than maximum pump flow rate or capac-
ity the sprayer can accommodate. Pump flow rate is
measured in gallons per minute (GPM).
Spray tip selection is based on paint viscosity,
paint type, & job needs. For light viscosities (thin
paints), use a smaller tip; heavier (thicker paints),
use a larger tip size.
For sizes not shown, call factory for availability.
TIP IDENTIFICATION:
1st 3-digits identifies it as a REV-TIP
TM
for airless paint spraying (P.N. 560-xxx) or a REV-TIP
TM
for airless line striping (P.N. 562-xxxST).
4th digit is the fan width - the number is half the fan width, e.g., 5 means a 10” fan.
5th and 6th digits
are for the orifice size and is measured in thousandths of an inch, e.g., 17 =
0.017 inch - The higher the number, the larger the tip.
. 029
Rev-Tip
TM
for Painting
P.N. 560-xxx
Protected By U.S. Patent No. 6,264,115 Other U.S. & Foreign Patents Applied For.
SPRAY TIP - ORIFICE SIZE
(Inches)
(water @ 2000psi, 138 bar)
(latex paint @ 2000psi,
138 bar/1.36 spec. gr.)
*Pump will support tip worn to next larger size.
Water Flow Rate
(gpm) .12 .18 .24 .31 .38 .47 .57 .67 .77 1.03 1.31 1.63 1.80
(lpm) .49 .69 .91 1.17 1.47 1.79 2.15 2.54 2.96 3.90 4.98 6.17 6.81
Paint Flow Rate
(gpm) .10 .15 .21 .27 .33 .40 .49 .58 .66 .88 1.12 1.39 1.54
(lpm) .38 .57 .79 1.02 1.25 1.51 1.85 2.20 2.50 3.33 4.24 5.26 5.83
Pump Minimum
(gpm) .25 .25 .33 .40 .50 .60 .75 .88 1.0 1.25 1.5 2.0 2.2
Output* (lpm) 1.0 1.0 1.25 1.5 1.9 2.3 2.8 3.3 3.8 4.7 5.7 7.5 8.2
Rev-Tip
TM
for Painting
Fan Width
(12” from surface)
in. (mm)
.009 .011 .013 .015 .017 .019 .021 .023 .025 .027 .031 .035 .039 .041
4-6 102-152
209 211 213 215 217 219 221 223 225 227 229
6-8 152-203
309 311 313 315 317 319 321 323 325 327
335
8-10 203-254
409 411 413 415 417 419 421 423 425 427 431
10-12 254-305
511 513 515 517 519 521 523 525 527 531 535
12-14 305-356
613 615 617 619 621 623 625 627 631 635 639 641
14-16 356-406
715 717 721 739
741 745
16-18 406-457 815 819 821 831
20-24 508-610
W21 W23 W25 W28 W29 W31
Gun Filter
C= Coarse - 60 mesh
F F F,C C C C C REMOVE FILTER
F= Fine - 100 mesh
Wood
Lacquer, Varnish
•
Interior
Stain, Sealer
• •
Enamel
•
Wood
Exterior Stain
• •
Exterior
Vinyl, Acrylic, Latex
• •
Masonry
Vinyl, Oil Base Alkyd
• •
Latex, Acrylic
• • • •
Block Filler
• • • • • • • •
Elastomer
• • •
• • • • •
Ceiling
Hi Build, Mil White
• •
Structural Steel
Heavy Coatings
• • • • • • • •
.
029
NEW Wide Tips
►
13