manualshive.com logo in svg

Airfilm Camera Systems AF200, Installation Instructions Manual

Share
Download
Airfilm Camera Systems AF200 Installation Instructions Manual Download Page 3

INSTALLATION INSTRUCTIONS            AF200-007 - REV E 

DATE 2/26/2015  

 

 Airfilm Camera Systems 

                                                                                               

Page 

3

 of 

31

 

 6245 Aerodrome Way Hangar No. 2 
 Georgetown, Ca 95634

 

 

AF200-2 NOSE MOUNT 

INSTALLATION INSTRUCTIONS: NOSE MOUNT SUPPORT

 

 

 

1) Confirm that the mount will not interfere with any exterior kits, antennas, and other 
exterior mounted assemblies. 
 
2) Remove the forward belly panel – Use caution for any antennas located on the panel. 
Disconnect any cabling before removing the panel.

 

 
3) Attach the 

HAMMER WEIGHT -T BRACKETS (A952) 

to the hammer weight existing 

bolts. Place the brackets up to the underside of the hammer weight attachment nuts. SEE 
FIG 1 - QUICK CLAMP A956 MAY BE SUBSTITUTED FOR A952 
 

 

FIG NO 1 

3A) Using a 6mm-socket remove an existing metric nut off of the hammer weight. Replace 
with special nuts and washers provided 6 each side 

(A700) 

 

Summary of Contents for AF200
































Reviews:

No comments

Brands by name

Popular brands

Load more brands