manualshive.com logo in svg

Airfilm Camera Systems AF200, Installation Instructions Manual

Share
Download
Airfilm Camera Systems AF200 Installation Instructions Manual Download Page 14

INSTALLATION INSTRUCTIONS            AF200-007 - REV E 

DATE 2/26/2015  

 

 Airfilm Camera Systems 

                                                                                               

Page 

14

 of 

31

 

 6245 Aerodrome Way Hangar No. 2 
 Georgetown, Ca 95634

 

 

 

 
2) Attach the 

COUNTER WEIGHT YOKE TENSION TUBE

 to the 

COMBO SIDE FITTING 

(A972)

.

 Use the following hardware

 (SEE ABOVE FIGURE) 

QTY  

TYPE – NUMBER 

ITEM 

1 

AN6-22A 

HEX HEAD BOLTS 

2 AN960-616 

WASHERS 

1 AN365-624A 

STOP 

NUTS 

Torque as per FAA AC43.13-1A   160-190 In Lbs. 
 

 

 

3) Attach the 

LOWER SIDE MOUNT SUPPORT ASSY (left and right) 

to the 

AIRCRAFT 

CROSS AFT CROSS TUBE

. Insure that the aircraft is properly protected by using the 

supplied (A795) rubber sleeve. 

Note:

 The counterweight supports are located inside of the 

side mount installation on the aft cross tube (See above figure) 
Additional rubber strips are used to protect the landing gear. 
Do not let the metal clamp come in contact with the landing gear. 
Attach using the items below for each side. 

 

QTY  

TYPE - NUMBER 

ITEM 

2 

AN6-37A 

HEX HEAD BOLTS 

4 AN960-616 

WASHERS 

2 AN365-624A 

STOP 

NUTS 

Torque as per FAA AC43.13-1A   160-190 In Lbs. 

Summary of Contents for AF200
































Reviews:

No comments

Brands by name

Popular brands

Load more brands