background image

 © STULZ S.p.A. – all rights reserved IT/10.2021/i04

WLA CompACT - TRANSLATIoN oF oRIGINAL INSTRUCTIoNS 

3. Residual risk

During transport and installation

Area

Danger

Risk

preventative measures

Under 

the unit

Defective lifting system of the 

unit, which causes its fall.

Contusions, 

trauma.

Keep away from the danger area while handling the 

unit.

Near the 

unit

Accidental shock with damage 

to the refrigerant circuit and leak 

of high pressure refrigerant.

Bruises, 

formation of 

acid vapours.

Keep away from the danger area while handling the 

unit. Wear PPE.

Near the 

unit

Unstable or unsuitable unit 

support that causes its overturn.

Contusions, 

trauma.

Make sure the unit support is adequate to its weight, is 

stable and levelled. Wear PPE.

Electrical 

box

Connection cables under 

voltage.

Electroshock Make sure to disconnect the power supply from the 

distribution panel.. Remain electrically insulated from 

the ground. Wear PPE.

During start-up and operation

Area

Danger

Risk

preventative measures

Near the unit

Suction and following expulsion of 

objects, dust, and substances from the 

fans in the installation site.

Contusions, trauma.

Clean the installation area. 

Wear PPE.

In contact with 

the unit

Non-compliant electrical connection 

and missing earth connection.

Electroshock.

Remain electrically insulated 

from the ground. Wear PPE.

Near water 

pipes

Closed shut-off valves; leaks from the 

hydraulic pipes. Consequent leaking of 

water and additives.

Irritation of skin and 

eyes due to contact 

with ethylene glycol. 

Irritation of the skin 

and breathing system 

due to glycol vapours. 

Electrocution, slipping.

Open the shut-off valves of the 

hydraulic circuit. Wear PPE.

Near water 

pipes

Condensate formation in the presence 

of the dew point with leaks of the not 

insulated pipes.

Electroshock, slipping.

Wear PPE.

Near the unit

With unit ON: Losses in the refrigerant 

circuit; defective safety valve and high 

pressure switch; fire; shut-off valves 

in the refrigerant circuit closed after 

maintenance; defect on the gas charge 

line. Consequent explosive breakage of 

the refrigerant circuit.

Bruises, formation of 

acid vapours with open 

flames..

Wear PPE. In case of fire, wear 

fire-fighting masks.

Near the unit 

(Electrical box, 

supply cables)

Short-circuit; incorrect sizing of the 

cables or of the main switch.

Electroshock, fire, 

formation of acid 

vapours.

Check the fixing of the terminal 

cables; select the power supply 

cables and main switch. Wear 

PPE. In case of fire, wear fire-

fighting masks.

Near the unit

Noise emission.

Injury of the hearing 

system.

Wear PPE.

During maintenance

Area

Danger

Risk

preventative measures

Near the unit

Losses in the refrigerant circuit; 

defective safety valve and high 

pressure switch; fire; defect on 

the gas charge line. Consequent 

explosive breakage of the 

refrigerant circuit.

Bruises, 

formation of 

acid vapours 

with open 

flames.

Wear PPE. In case of fire, wear fire-

fighting masks.

Components of the 

unit: compressor, 

delivery pipes, 

condenser

Contact with hot surfaces.

Bruises.

Avoid the contact. Wear PPE.

Condenser

Contact with sharp surfaces (fins).

Cuts, 

abrasions.

Wear PPE.

11

Summary of Contents for WLA Compact 230/1/50



























































Reviews: