background image

EN/10.2021/i04  © STULZ S.p.A. – all rights reserved

WLA CompACT - TRANSLATIoN oF oRIGINAL INSTRUCTIoNS

WLA CompACT - TRANSLATIoN oF oRIGINAL INSTRUCTIoNS

problem

possible cause

Recommended intervention

9. The chiller runs

continuously

No refrigerant gas

See point 7

Incorrect thermostat configuration

Check and restore the original configuration

Excessive thermal load

Reduce thermal load

10.

The chiller 

runs but does not 
cool down

No refrigerant gas

See point 7

Presence of humidity in the refrigerant 
circuit

Discharge, dry the circuit, replace the filter, make vacuum and 
recharge.

Open hot gas bypass valve

Check and/or replace it

11.

 The chiller 
produces
anomalous

noise

Noisy compressor

Scroll compressor with incorrect rotation. Check the 
correspondence between the motor winding connection and 
the electrical diagram on the motor. Invert the phases in order 
to comply with the correct rotation.

Noisy thermostatic valve

Check and/or replace it

Vibrations coming from the pipes

Check and/or bracket the pipes

Noisy body

Check the fixing of the hardware

11. Decommissioning and disposal

of the unit

The decommissioning of the chillers must be carried out by experienced and qualified personnel.

  

DANGER

This unit contains refrigerant and a small quantity of lubricant (ester) inside its compressor. 
These substances are dangerous for the environment and must not be dispersed in it. 
Refrigerants containing fluorocarbons contribute to global warming and consequently to 
climate changes.  They must be disposed of in accordance with disposal standards or they 
must be delivered to firms qualified as specialized waste disposal firms.

  

WARNING

Cut off power supply. Switch off power conducting cables to the unit and secure them 
against being switched on again. Disconnect the A/C unit from the de-energized network.

Move the unit as described in paragraph “Moving and storage”, with a lifting device of suitable 
capacity. The following are the instructions for proper disposal of the unit during the various 
phases of its life. For further clarification or additional information, please contact [email protected].

  

INFoRmATIoN

To  ensure  proper  and  safe  disposal  activities,  operator  must  equip  themselves  with  the 
necessary  PPE  including:  anti-cut  gloves,  oil  resistant  gloves,  heat  resistant  gloves,  safety 
footwear, safety eyewear against liquid and gas splashes.
The  context  in  which  the  unit  is  located  may  require  the  use  of  additional  PPE,  thus  it  is 
mandatory to inquire with the relevant staff of the area before starting operation.

Once the materials have been separated as shown below, they should be assigned EWC codes 
and then sent for disposal in accordance with the national legislation.
Disposal related to the unit purchased occurs in three stages:

50

50

Summary of Contents for WLA Compact 230/1/50



























































Reviews: