background image

EN/10.2021/i04  © STULZ S.p.A. – all rights reserved

WLA CompACT - TRANSLATIoN oF oRIGINAL INSTRUCTIoNS

WLA CompACT - TRANSLATIoN oF oRIGINAL INSTRUCTIoNS

Area

Danger

Risk

preventative measures

Electrical box

Live power supply line even if the 

switch on board the unit is OFF.

Electroshock

Make sure to disconnect the power 

supply from the distribution panel. 

Make sure that the main switch is not 

reactivated during maintenance.

During dismantling

Area

Danger

Risk

preventative measures

Near the 

unit

Losses in the refrigerant circuit; 

defective refrigerant recovery 

system. Consequent explosive 

breakage of the refrigerant circuit.

Bruises, formation 

of acid vapours with 

open flames..

Wear PPE.

Near the 

unit

Oil leaks during recovery.

Oil contact wit skin 

or eyes

Wear PPE.

Near 

water 

pipes

Unscrewing the water pipes still 

under pressure.

Irritation of skin and 

eyes due to contact 

with ethylene 

glycol.. Electro-

shock. Slipping

De-pressurise the hydraulic circuit before 

disconnection. Wear PPE.

Electrical 

box

Live power supply line even if the 

switch on board the unit is OFF.

Electroshock.

Make sure to disconnect the power 

supply from the distribution panel. 

Make sure that the main switch is not 

reactivated during maintenance.

3.1. 

Refrigerant safety data

Refrigerant safety data

1.

 Identification of 

the substance/

preparation

Identification of the preparation STAR COLD 134a

Recommended uses

Refrigerant

2. 

Composition 

/ information on 

the ingredients

Tetrafluoroethane (C2H2F4)

N° CAS: 811-97-2

N° CE: 212-377-0

Concentration: 100%

3. Identification of 

the hazards

Possible Hazards

Not dangerous according to Directive 1999/45/EC. Consequences on the 

environment: not readily biodegradable. Physical and chemical hazards: thermal 

decomposition in toxic and corrosive products.

4. 

Fire-fighting 

measures

Inhalation

Move the victim to a non-contaminated area wearing  breathing equipment. Keep 

the patient warm and at rest. Call a doctor. Apply artificial respiration if breathing has 

stopped.

Contact with skin

In case of frostbite, spray with water for at least 15 minutes. Apply a sterile gauze. 

And obtain medical assistance.

Contact with eyes

Immediately wash the eyes with water for at least 15 minutes.

Ingestion

Ingestion is not considered a potential route of exposure.

Protection for first-aiders

Wear suitable respiratory equipment in case of interventions in saturated atmosphere.

Notes for the doctor

Do not administer catecholamines (due to the cardiac effects of the product)

5. Fire-fighting 

measures

Suitable extinguishing medium Adopt extinguishing measures in fire area.

Special risks from the 

substance or mixture

The product is not flammable in ambient pressure and temperature. Any mixtures, 

under pressure with air, can be flammable. At high temperature: There is thermal 

decomposition into toxic and corrosive products as hydrofluoric acid and carbon 

oxides.

Advice for fire-fighters

Cool containers/tanks with spraying water. Provide a rapid container evacuation 

system. In case of fire nearby, keep away containers exposed to fire. In case of fire, 

wear a self-contained breathing apparatus and a complete protection suit against 

chemical agents.

6. Accidental 

release measures

Individual measures

Try to stop the leakage. Evacuate the area. Ensure suitable ventilation. Use the 

respiratory equipment to access the involved area unless atmosphere is proved 

to be unbreathable. Avoid accessing sewers, basements, or any place where its 

accumulation could be dangerous.

Environmental precautions.

Try to stop the leakage.

Methods and materials for 

containment and recovery

Ventilate the area.

12

12

Summary of Contents for WLA Compact 230/1/50



























































Reviews: