Air Oasis NANO INDUCT Sanifier Owner'S Manual Download Page 11

Maintenance

AHPCO

®

 Cell Replacement Process

The entire Cell should be replaced every two years. Failure to replace the Cell 

will decrease the effectiveness of the unit. After two years of use the blue Lamp 

Replacement light will begin to blink as a reminder that it’s time to replace the AH-

PCO

®

 Cell. 

Note: UV lamps contain Hg (Mercury) and should be disposed of according to dis-

posal laws. Find disposal centers at www.earth911.org.

We recommend contacting a licensed HVAC professional to perform the replace-

ment process.

1.  Unplug the NIND from its power source.

2.  Remove  the  four  screws  securing  the  Ballast 

Assembly and pull the Ballast Assembly away 

from the Retainer Ring until the four pins have 

completely  disconnected  from  the  Ballast As-

sembly.

3.  Remove the four screws securing the AHPCO

®

 

Cell and pull the AHPCO

®

 Cell out from the Re-

tainer Ring. Properly dispose of the AHPCO

® 

Cell.

4.  Insert  the new AHPCO

®

 Cell and secure with 

four 1/4” hex head screws. Do not overtighten the screws.

5.  Using  a  small  cylindrical  object,  such  as  a  pen,  press 

and hold the Lamp Reset Button for 3 seconds. This will 

reset the Lamp Replacement Indicator. The Lamp Reset 

Button is located on the bottom of the Ballast Assembly.  

6.  Press  the  Ballast  Assembly  onto  the  four  pins  protruding  from  the  AH-

PCO

®

  Cell.  The  Ballast  Assembly  should  be  orientated  with  the  “air 

flow”  label  running  parallel  with  the  length  of  the  duct  to  ensure  the  four 

pins are in line with the Four Pin Connector. Optional mounting con-

figurations,  such  as  opening  the  UV  shields,  may  vary  the  orientation 

of  the  “air  flow”  label.  It’s  only  intended  to  serve  as  a  general  guideline. 

7.  Using a 1/4” hex head screw driver, secure the NIND with four self tap-

ping 3/4” screws being careful not to overtighten stripping the screw holes.  

Lamp Reset Switch

nano Induct Limited Warranty

Air Oasis gives you the following limited warranty for this product only if it was origi-

nally purchased directly from Air Oasis or an Air Oasis authorized dealer.

Air Oasis will repair or replace, free of charge to the original purchaser, any part 

that is found to be defective in material or workmanship within two (2) years of the 

date of purchase. The warranty automatically renews for an additional two years 

when the AHPCO

®

 Cell is replaced within two years.

This  limited  warranty  does  not  apply  to  any  part  subjected  to  accident,  abuse,  

alteration, misuse, lack of reasonable care, the affixing of any attachment not pro-

vided with the product, loss of parts, damage caused by acts of God, the use of 

voltages other than indicated on the label displayed on this product or service of 

this product by anyone other than Air Oasis or an Air Oasis authorized dealer.

Air Oasis does not authorize any person or dealer to assume or grant any other 

warranty obligation with the sale of this product.

To obtain service, the customer must first register this unit by returning the en-

closed Warranty Card.  If you purchase this product from any source other than 

Air Oasis or an Air Oasis dealer, your purchase is “AS IS”, which means Air Oasis 

grants you no warranty, and that you, not Air Oasis, assume the entire risk of the 

quality and performance of this product, including the entire cost of any necessary 

servicing or repairs of any defects.

Air Oasis’ liability for damages to you for any costs whatsoever arising out of this 

statement of limited warranty shall be limited to the amount paid for this product 

at the time of original purchase, and Air Oasis shall not be liable for any direct, 

indirect, consequential or incidental damages arising out of the use or inability to 

use this product.

ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT, INCLUDING 

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTIC-

ULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD, 

AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AF-

TER THIS PERIOD.

Some states do not allow limitations on the duration of implied warranties, so the 

above limitation may not apply to you.  This warranty gives you specific legal rights, 

and you may also have other rights which vary from state to state.

To obtain service and RMA number, contact an Air Oasis representative at:

1-800-936-1764

NOTE: An RMA# and proof of purchase is required for any warranty service 

work. All returned packages that do not have an RMA# will be refused.

9

Summary of Contents for NANO INDUCT Sanifier













Reviews: