manualshive.com logo in svg

Air Live WHA-5500CPE, User Manual

Share
Download
Air Live WHA-5500CPE User Manual Download Page 58

4. Web Management-Wireless and WAN Settings 

 

 

AirLive WHA-5500CPE User’s Manual 

52

 

 

To Enable RADIUS Server: 

„

 

Server IP: 

The IP address of the RADIUS server.   

„

 

Port Number: 

The port number that your RADIUS server uses for authentication. The 

default setting is 1812.   

„

 

RADIUS Type: 

RADIUS 

„

 

Shared Secret: 

This is used by your RADIUS server in the Shared Secret field in 

RADIUS protocol messages. The shared secret configured in the WHA-5500CPE must 
match the shared secret configured in the RADIUS server. The shared secret can 
contain up to 64 alphanumeric characters.   

„

 

RADIUS Server Reattempt Period: 

The number of times the WHA-5500CPE should 

attempt to contact the primary server before giving up 

 
 
 

4.2.18 Bandwidth Control 

Operation Mode -> Setup -> Bandwidth Control

 

Bandwidth Control can limit the maximum speed of entire wireless interface or individual 
device.  It is also known as Traffic Shaping.  The WHA-5500CPE provides both Total 
Bandwidth and Per-User Bandwidth Control for both uplink and downlink speed.  It 
controls the speed of both wireless and wired interface. 
 

Summary of Contents for WHA-5500CPE

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands