manualshive.com logo in svg

Air Live WHA-5500CPE, User Manual

Share
Download
Air Live WHA-5500CPE User Manual Download Page 35

4. Web Management-Wireless and WAN Settings 

 

 

 

29 

                       

AirLive WHA-5500CPE User’s Manual

 

 
 
 
 
 
 
 
 

 
In this chapter, we will explain about the wireless settings and router mode settings in web 
management interface.  Please be sure to read through Chapter 3’s “

Introduction to Web 

Management” 

and

 “Initial Configurations” 

first.    For system configurations, device status, 

and other non-wireless related settings; please go to Chapter 5.     
 

4.1 About WHA-5500CPE’s Menu Structure 

The WHA-5500CPE’s web management menu is divided into 3 main menus: 

Operation 

Modes, System Configurations

, and 

Device Status

.    The main menus are displayed in 

“Top Menu Bar”.    Within each main menu category, there are sub-menu options which are 
displayed on the “Side Menu Bar” 

 

 
 
 
 
 
 
 
 
 

 

„

 

Operation Mode

:    This menu is where you will find wireless and WAN settings.   

The WHA-5500CPE’s wireless settings are dependant on the wireless operation 
mode you choose; only the applicable wireless settings for selected operation 
mode are shown.    For example; WAN port setting is available only for AP Router 
and WISP Router mode, it will only be shown in those modes. To access wireless 
settings, click on the “

Setup

” button within each operation mode.  For explanation 

on different wireless modes, please refer to Chapter 1.  We will talk about 
functions in this menu for this chapter. 

„

 

System Configuration: 

All settings besides Wireless and WAN functions are in 

this category.  The system configuration including changing password, upload 
firmware, backup configuration, settings PING watchdog, and setting management 
interface.    We will talk about this menu’s function in Chapter 5.

 

4 

4. 

Web Management: 

Wireless and WAN 

Settings

 

 

TOP Menu Bar: Main

Side Menu Bar: Sub

Language

Summary of Contents for WHA-5500CPE

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands