manualshive.com logo in svg

Air Live SNMP-GSH2004L, User Manual, Page: 55 / 61

Share
Download
Air Live SNMP-GSH2004L User Manual Download Page 55

4. Web Management 

 
 
 
 

 

AirLive SNMP-GSH2004L User’s Manual 

50

4.6.1 Warm Restart   

Reboot the switch. Reboot takes the same effect as the RESET (mode) button on the front 
panel of the switch. Press 

<Yes> 

button to confirm warm restart function and it will take 

around thirty (30) seconds to complete the system boot. 

 

 

4.6.2 Factory Default   

Factory Default provides the function to retrieve default settings and replace current 
configuration. Except the IP address setting, all settings will be restored to the factory 
default values when “Factory Default” function is performed. If you want to restore all 
configurations including the IP address setting to the factory default, please press the 
“RESET” (mode) button on the front panel. 
 

¾

  Note for “RESET” (mode) button: 

You must press the “RESET” (mode) button over 10 seconds to restore the factory default 
setting. 

 

 

 

4.6.3 Software Upload   

You can just click Browse button to retrieve the file you want in your system to upgrade your 
switch. 

 

Summary of Contents for SNMP-GSH2004L






























































Reviews:

No comments