manualshive.com logo in svg

Air Live SNMP-GSH2004L, User Manual, Page: 10 / 61

Share
Download
Air Live SNMP-GSH2004L User Manual Download Page 10

2. Installation of the Switch 

AirLive SNMP-GSH2004L User’s Manual 

5

 

 

¾

 

LED Indicators: 

Comprehensive LED indicators display the status of the switch and the network (see the 
LED Indicators chapter below). 

 

¾

 

1000BASE-T Gigabit Ethernet Ports (Port 1~24) 

The Switch four Gigabit twisted pair ports, supported auto negotiable 10/100/1000Mbps 
and auto MDI/MDIX crossover detection function, this function gives true “plug and play” 
capability, just need to plug-in the network cable to the hub directly and don’t care if the end 
node is NIC (Network Interface Card) or switch and hub. These ports can operate in 
half-duplex mode for 10/100Mbps and full- duplex mode for 10/100/1000Mbps. 

 

¾

 

Combo SFP Ports (Port 21~24) 

The Switch is equipped with four combo SFP ports, supported optional 1000BASE-SX/LX 
SFP module. The 1000BASE-T port 21~24 are the same ports with the SFP port 21~24, 
when plug in the SFP module, the device will activate SFP, and the RJ45 port will be 
disabled. 
 

* Note

: When the port was set to “Forced Mode”, the Auto MDI/MDIX will be disabled. 

 

¾

 

Mode button: 

The Mode button is to change the LED’s status to Link/Act or Speed, and reset all the 
setting back to the factory default by pressing the mode button for 10 seconds. 
 

* Note: 

Be sure that you recorded the setting of your device; else all the setting will be 

erased when pressing the “

Mode

” (reset) button 10 seconds. 

 

Summary of Contents for SNMP-GSH2004L






























































Reviews:

No comments