Air Live SNMP-GSH2004L User Manual Download Page 15 | Manualshive

Page: 15 / 61

Air Live SNMP-GSH2004L User Manual Download Page 15

2. Installation of the Switch

AirLive SNMP-GSH2004L User’s Manual

10

2.7 Connecting to Power

SNMP-GSH2004L

features a universal auto-select power supply unit, which allows a power

connection to a wide range of input voltages from 100 to 240VAC @ 50 ~ 60Hz.
To establish its power connection, simply plug the female end of the power cord into the
power connector on the rear of the switch and the male end of the power cord into a
suitable power outlet. Once you have correctly plugged in the power, you can then turn on
the Power Switch to activate the switch.

2.8 Reset to Default

When you forgot your IP or password, please use the mode (reset) button for the factory
default setting. Please take the following steps to reset the Web Smart Switch back to the
original default:

Step 1.

Turn on the

SNMP-GSH2004L

.

Step 2.

Press and hold the mode (reset) button continuously for 10 seconds and
release the mode (reset) button.

Step 3.

The switch will reboot for 30 seconds and the configuration of switch will
back to the default setting.

Key in the user ID and the password to pass the authentication; the default ID and
Password is as below,

IP Address: 192.168.2.1
Password:

airlive

«
...
13
14
15
16
17
...
»

Summary of Contents for SNMP-GSH2004L






























































Reviews:

No comments