manualshive.com logo in svg

Air Live SNMP-GSH2004L, User Manual, Page: 33 / 61

Share
Download
Air Live SNMP-GSH2004L User Manual Download Page 33

4. Web Management 

 
 
 
 

 

AirLive SNMP-GSH2004L User’s Manual 

28

„

  System Priority: This parameter configures the spanning tree priority globally for this 

switch. The device with the highest priority becomes the STP root device. However, if 
all devices have the same priority, the device with the lowest MAC address will then 
become the root device. Number between 0 - 61440 in increments of 4096. Therefore, 
there are 16 distinct values. 
 

„

  Hello Time: Interval (in seconds) at which the root device transmits a configuration 

message (BPDU frame). Number between 1-10 (default is 2). 

 

„

  Max Age – The maximum time (in seconds) a device can wait without receiving a 

configuration message before attempting to reconfigure. That also means the 
maximum life time for a BPDU frame. Number between 6-40 (default is 20). 
 

„

  Forward Delay: The maximum time (in seconds) the root device will wait before 

changing states (i.e., discarding to learning to forwarding). Number between 4–30 
(default is 15) 

Summary of Contents for SNMP-GSH2004L






























































Reviews:

No comments