manualshive.com logo in svg

AIR DRYER SUPPLIER CATR-1600-200, Instruction Manual, Page: 49 / 57

Share
Download
AIR DRYER SUPPLIER CATR-1600-200 Instruction Manual Download Page 49

Material Safety Data Sheet 

3/16" Activated Alumina Desiccant 

Revision date : 2014/06/19 

Page 7 of 8 

Version: 6.0 

(53732394/SDS_GEN_US/EN) 

Persistence and degradability 

Assessment biodegradation and elimination (H2O) 
Not applicable for inorganic substances. 

Additional information 

Other ecotoxicological advice: 
The product has not been tested. The statements on ecotoxicology have been derived from the properties of the 
individual components. The product has been assessed on the basis of the components’ available data. To some 
extent data gaps exist for individual components. According to our present knowledge and experience dangers 
which are not covered by the current labeling are not to be expected. 

13. Disposal  considerations 

Waste disposal of substance: 

Dispose of in accordance with local authority regulations. Check for possible recycling. Disposal requirements are 
dependent on the hazard classification and will vary by location and the type of disposal selected. All waste 
materials should be reviewed to determine the applicable hazards (testing may be necessary). 

14. Transport  Information 

Land transport 

USDOT 
Not classified as a dangerous good under transport regulations 

Sea transport 

IMDG 
Not classified as a dangerous good under transport regulations 

Air transport 

IATA/ICAO 
Not classified as a dangerous good under transport regulations 

15. Regulatory  Information 

Federal Regulations 
Registration status: 

Chemical TSCA, US released / listed 

NFPA Hazard codes: 

Health : 1 

Fire: 0 

Reactivity: 0 

Special: 

HMIS III rating 

Health: 1 

Flammability: 0 

Physical hazard: 0 

Assessment of the hazard classes according to UN GHS criteria (most recent version): 

Summary of Contents for CATR-1600-200


























































Reviews:

No comments