manualshive.com logo in svg

AIR DRYER SUPPLIER CATR-1600-200, Instruction Manual, Page: 20 / 57

Share
Download
AIR DRYER SUPPLIER CATR-1600-200 Instruction Manual Download Page 20

AIR DRYER SUPPLIER, INC. 

AIR DRYER INSTRUCTION MANUAL 

Model CATR 

Reference ADS-316 

 

Rev 0 

Page 20 of 40 

 

03/22/2019 

 

SECTION 3: COOLER ASSEMBLY 

3.2 

The Pneumatic Motor And Cooling Fan Blade 

The pneumatic motor and cooling fan blade provided is relatively maintenance free 
and there are only a few points that should be followed to assure satisfactory 
performance. Review the bullet points during installation and operation.  

Note: 

The fan blade assembly should be inspected at time of installation and after 
every 4 weeks of operation to ensure integrity of the fan blades. DO NOT 
attempt to repair a damaged fan blade. A damaged fan assembly should only 
be replaced with factory original part. The air supply line to the cooler motor-
fan assembly should be disconnected if fan service is to be performed. A 
damaged pneumatic motor can affect the integrity of the fan blades. If the 
cooler pneumatic motor fails the fan blade assembly should be inspected for 
stress cracks by a qualified person, or have the fan blade assembly replaced. 
The cooling fan may need replacement every 1-2 years depending on severe 
duty found at site. 

Caution! 

The exhaust stream from the pneumatic motor may contain solid particles or 
oil aerosol. Wear eye and skin protection at all times while in the proximity of 
this equipment. 

  Ensure the oil mist delivery to the motor is properly adjusted. A data table of 

adjustments has been provided at the end of this section. 

  Ensure pneumatic motor outlet muffler is clean and unobstructed of dirt particles 

that will prevent normal operation of the motor. 

  Ensure the delivery pressure to the motor is set per the data table provided at the 

end of this section. 

  For long term storage (several weeks) the motor should be properly lubricated at 

time of start up to ensure trouble free and long term performance. 

Important! 

The pneumatic cooler motor provided requires oil lubrication. The type of oil 
recommended is a non-detergent SAE#10 air tool oil. Flushing of the motor may be 
required to remove excessive dirt, foreign particles moisture or oil. Use only air tool 
flushing solvent. Do not use kerosene or any other type of combustible solvents to 
flush motor. 

Summary of Contents for CATR-1600-200


























































Reviews:

No comments