Aimco AcraDyne Gen III 2000 Series Operation Manual Download Page 9

Page: 9 / 12

- Units: RPM of the tool output

- Default: 90 RPM

- Range: 1 to 200 RPM

- Obstruction Check Acceleration Limit

- Rate at which the speed of the tool ramps to Obstruction Check Speed.

- Units: kRPM/second

- Default value: 0.5

- Range: 0.1 to 10

ube

omINg

TarT

NpuT

ogIc

elecTIoN

The controller parameters for tube- operation can be viewed and modified from the Controller->Edit Controller Parameter-
>Tube Nut screen in ToolWare.

•

Tube nut Home Strategy:

- Lever action required to start the home sequence.

- Options:

Home on release and repress of the lever (default)

Home on release of the lever

geN IV c

oNTroller

arameTers

ffecTINg

ube

INcH

eTecTIoN

oNT

’

)

Summary of Contents for AcraDyne Gen III 2000 Series













Search results

Summary of Contents for AcraDyne Gen III 2000 Series

Reviews:

Related manuals for AcraDyne Gen III 2000 Series

Brands by name

Popular brands

Aimco AcraDyne Gen III 2000 Series, Operation Manual

Search results

Summary of Contents for AcraDyne Gen III 2000 Series

Reviews:

Related manuals for AcraDyne Gen III 2000 Series

Brands by name

Popular brands