background image

© 2006-Present Agrowtek Inc. 

www.agrowtek.com

 | 200 N Anets Dr. Northbrook, IL 60062 | [email protected] 

4

 

 

Connecting Equipment

 

 

Input Voltage:  
GrowControl operates on AC pwoer between 90 and 240 VAC (47-63Hz.)  
 
The input voltage will be passed to the equipment outlets when 
they are activated. 
 
GrowControl comes with eight (8) outlets that control up to six (6) pieces 
of equipment.   
 
Each equipment output can handle 8 Amps Resistive/2 Amps 
Inductive
 @ 120/240VAC (1000 Watts) 

 

The controller can handle a maximum of 15 Amps (resistive) combined. 
 
Extension Cords may be used to connect equipment to the controller.  
Ensure the cord it the proper type and gauge to handle the conditions 
and power load. 
 
If your equipment requires greater current than 8 Amps or a different 
voltage than supplied by the controller, a high-power relay must be 
used. High power relays plug into the equipment outputs and act as a 
switch to turn on power to the equipment from another circuit. 

 

 
 

 

 
 

 

 

 
 

 

 
 

 

 
 

 

 

Receptacle Assignments 

Typical Application Example 

Summary of Contents for GrowControl























Reviews: