background image

© 2006-Present Agrowtek Inc. 

www.agrowtek.com

 | 200 N Anets Dr. Northbrook, IL 60062 | [email protected] 

21

 

 

Limited Warranty 

 
Agrowtek Inc. warrants that all manufactured products are, to the best of its knowledge, 

free of defective material and workmanship and warrants the components for the following 

period from the date of purchase: 

 
GrowControl

TM

 Controller System: 

2 Years 

Sensors & Accessories: 

 

1 Year 

 
This warranty is extended only to the original purchaser of the equipment from the date of 

purchase detailed on the purchase invoice.  

 
This warranty does not cover damages from abuse, accidental breakage, or units that have 

been modified, altered, or installed in a manner other than that which is specified in the 

installation instructions. 

 
Agrowtek Inc. must be contacted prior to return shipment for a return authorization. No 

returns will be accepted without a return authorization. The original purchase invoice must 

accompany any warranty claims.  
 

This warranty is applicable only to products that have been properly stored, installed, and 

maintained per the installation and operation manual and used for their intended purpose. 
This limited warranty does not cover products installed in or operated under unusual 

conditions or environments including, but not limited to, high humidity or high temperature 

conditions.  

 
The products which have been claimed and comply with the aforementioned restrictions 

shall be replaced or repaired at the sole discretion of the Agrowtek Inc. at no charge.  

 
This warranty is provided in lieu of all other warranty provisions, express or implied. It is 

including but not limited to any implied warranty of fitness or merchantability for a particular 

purpose and is limited to the Warranty Period.  
 

In no event or circumstance shall Agrowtek Inc. be liable to any third party or the claimant 

for damages in excess of the price paid for the product, or for any loss of use, 

inconvenience, commercial loss, loss of time, lost profits or savings or any other incidental, 
consequential or special damages arising out of the use of, or inability to use, the product. 

This disclaimer is made to the fullest extent allowed by law or regulation and is specifically 

made to specify that the liability of Agrowtek  Inc.  under  this  limited  warranty,  or  any 
claimed extension thereof, shall be to replace or repair the Product or refund the price paid 

for the Product. 

 
This warranty provides the purchaser with specific rights but the claimant may have other 

rights which vary from jurisdiction to jurisdiction. 

 

 

Summary of Contents for GrowControl























Reviews: