Agri-Fab LST42C Owner'S Manual Download | Manualshive

Page: 9 / 36

background image

9

3/8" X 3-1/4"
HEX BOLT
(A)

LARGE SPACER (MM)

PULLEY (NN)

3/8" LOCKWASHER (O)

3/8" HEX LOCK NUT (Z)

3/8"
WASHER (T)

LONG END
OF HUB

STeP 7: (See FIGure 7)
• Attach the pulley (long end of hub facing down) and

the large spacer (MM) to the hole shown in the clutch/

idler assembly. Use a 3/8" x 3-1/4" hex bolt (A), a 3/8"
washer (T), a 3/8" lock washer (O) and a 3/8" hex lock

nut (Z).

FIGure 7

FIGure 9

STeP 9: (See FIGure 9)
• Attach the cable bracket to the slot shown in the

clutch/idler assembly using a 5/16" x 3/4" carriage
bolt (K) and a 5/16" nylock nut (Y). Place the bolt in
the front hole of the bracket and in the end of the slot

closest to the pulley.

Do not tighten yet.

CABLE
BRACKET

5/16" x 3/4"
CARRIAGE BOLT (K)

5/16" NYLOCK
NUT (Y)

THIS SeCTIoN IS For TraCTorS wITH a
MaNuaL aTTaCHMeNT CLuTCH

If your tractor has an electric attachment clutch go to
step 14 on page 11.

FIGure 10

HEX BOLTS

(#48138)
DRIVE BELT

FLAT IDLER
PULLEYS

SToP

Did you select the correct drive belt for your
tractor? Using the wrong length belt may
cause premature bearing or belt failure.

STeP 10: (See FIGure 10)
• Two different length drive belts are included with

your snow thrower. Tractors with manual attachment
clutches and single front deck suspension brackets use
the 56" drive belt with

#48138

printed on the outside of

the belt.

Do NoT uSe the other belt.

• Slightly loosen the hex bolt next to the flat idler pulley.

Install the drive belt down between the hex bolt and the
flat idler pulley with the flat side of the belt against the
pulley. Retighten the hex bolt.

• Loop the belt around the large v-pulley, placing it

between the v-pulley and the hex bolt next to the pulley.
Place the belt to the inside of the other flat idler pulley.

5/16" NYLOCK
NUT (Y)

5/16" x 3/4"
HEX BOLT (C)

TENSIONING CHAIN (JJ)

FIGure 8

STeP 8: (See FIGure 8)
• Attach the two suspension arms to the rear of the

clutch/idler assembly using two 5/16" x 3/4" hex bolts
(C) and 5/16" nylock nuts (Y) for each arm. Place the
arms on the outside of the frame with the notches to

the rear.

• Insert a tensioning chain through the hole shown and

attach the end link to the spring on the lower idler arm.

«
...
7
8
9
10
11
...
»

Summary of Contents for LST42C





































Reviews:

No comments

Related manuals for LST42C

Brand: Simplicity Pages: 24

Brand: Blizzard Pages: 52

Brand: Simplicity Pages: 26

Brand: Kärcher Pages: 178

Brand: Yard-Man Pages: 32

Brand: Daniels Pages: 16

Brand: Yardworks Pages: 80

Brand: White Outdoor Pages: 22

Brand: SNOWJOE Pages: 2

Brand: SNOWJOE Pages: 8

Brand: SNOWJOE Pages: 8

Brand: SNOWJOE Pages: 16

Brand: SNOWJOE Pages: 16

Brand: SNOWJOE Pages: 13

Brand: SNOWJOE Pages: 16

Brand: SNOWJOE Pages: 20

Brand: SNOWJOE Pages: 20

Brand: SNOWJOE Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands