Agri-Fab LST42C Owner'S Manual Download

Page: 8 / 36

STeP 4: (See FIGure 4)
•

Assemble a shoulder bolt (L) and a 3/8" washer (T) to

the outside of R.H. side plate, securing it with a 3/8"

flanged nut (X). Repeat for L.H. side plate.

FIGure 4

rIGHT SIDe VIew

FIGure 3

rIGHT SIDe VIew

5/16"
NYLOCK
NUT (Y)

5/16" x 1"
CARRIAGE BOLT (J)

ENGINE MOUNTING
PLATE

(4) 1/2" WASHERS (R)

(3) 3/8" FLANGE NUTS (X)

(3) 3/8" x 1"
CARRIAGE
BOLTS (G)

SEE NOTE

3/8" WASHER (T)

SHOULDER
BOLT (L)

3/8" FLANGED
NUT (X)

INSTaLL SIDe PLaTeS

STeP 3: (See FIGure 3)
• Fasten the R.H. Side Plate (bend facing out) to the

front three holes in the tractor frame using three 3/8"
x 1" carriage bolts (G), three 1/2" washers (R) (see
note) and three 3/8" flange nuts (X).

For the rear hole,

use a 5/16" x 1" carriage bolt (J), a 1/2" washer (R)
and a 5/16" nylock nut (Y).

Place the 1/2" washers (R)

between the tractor frame and the side plate. Repeat

for L.H. side plate.

• Reinstall the browning shield onto the tractor frame

using the original screws.

NoTe: If there is an engine mounting plate (shown with
dotted lines) leave the 1/2 washer off the bolt that goes

through the plate.

INSTaLL HaNGer BraCKeTS aND SHouLDer
BoLTS To ouTSIDe oF FraMe

STeP 5: (See FIGure 5)
•

Remove the bolt, if present, in the hole directly behind
the brake rod on the left side of the tractor frame.

• Attach the L.H. Hanger Bracket (tube facing out) to the

hole using a 5/16" x 3/4" self threading bolt (F).

• Install a round head shoulder bolt (M) into the hole

that is 9-1/2" to the rear of the bolt you just installed.
Secure it with a 3/8" flange nut (X) on the inside of the
frame.

FIGure 5

LeFT SIDe VIew

5/16" x 3/4" SELF
THREADING BOLT (F)

L.H. HANGER

BRACKET

BRAKE ROD

3/8" FLANGED
NUT (X)

SHOULDER
BOLT (M)

5/16" x 3/4" SELF
THREADING BOLT (F)

R.H. HANGER
BRACKET

RIGHT END OF
BRAKE ROD

3/8" FLANGED
NUT (X)

SHOULDER
BOLT (M)

STeP 6: (See FIGure 6)
•

Remove the bracket, if present, from the hole directly
behind the end of the brake rod on the right side of
the tractor frame. Store the bracket and bolt.

• Attach the R.H. Hanger Bracket to the hole using a

5/16" x 3/4" self threading bolt (F).

• Install a round head shoulder bolt (M) into the hole

that is 9-1/2" to the rear of the bolt you just installed.
Secure it with a 3/8" flange nut (X) on the inside of the
frame.

FIGure 6

rIGHT SIDe VIew

Summary of Contents for LST42C





































Search results

Summary of Contents for LST42C

Reviews:

Related manuals for LST42C

Brands by name

Popular brands

Agri-Fab LST42C, Owner'S Manual

Search results

Summary of Contents for LST42C

Reviews:

Related manuals for LST42C

Brands by name

Popular brands