Agri-Fab LST42C Owner'S Manual Download | Manualshive

Page: 17 / 36

background image

17

FIGure 36

FIGure 38

STeP 36: (See FIGure 36)
• Assemble the cable bracket to the clutch/idler

assembly using two 5/16" x 3/4" carriage bolts (K) and
5/16" nylock nuts (Y). Use the two front holes in the
cable bracket if your tractor has a 42" mower deck.
Use the two rear holes if your tractor has a 46" mower
deck.

STeP 38: (See FIGure 38)
• Move the attachment clutch lever on the dash panel to

the disengaged (down) position.

• Place the clutch/idler assembly on the floor on the right

side of the tractor.

• Attach the tractor's clutch cable to the cable bracket.

Secure the cable housing guide (groove down) to the
cable bracket using the original collar and a 5/64" hair

cotter pin (DD).

• Place a spacer (LL) on the welded pin on the idler arm.

Hook the end of the clutch spring over the pin and

secure it with a 1/4" washer (P) and a 5/64" hair cotter
pin (DD).

CABLE
BRACKET

5/16" x 3/4"
CARRIAGE BOLT (K)

5/16" NYLOCK
NUT (Y)

42"

DECKS

46"

DECKS

GROOVE

TRACTOR'S
CLUTCH CABLE

5/64" HAIR
COTTER PIN (NN)

1/4" WASHER (X)

SPACER (HH)

TRACTOR'S
CLUTCH CABLE

5/64" HAIR
COTTER PIN (DD)

1/4" WASHER (P)

SPACER (LL)

5/64" HAIR
COTTER PIN (DD)

STeP 35: (See FIGure 35)
• Attach the two suspension arms to the rear of the

clutch/idler assembly using two 5/16" x 3/4" hex bolts
(C), 5/16" washer (Q) and 5/16" nylock nuts (Y) for
each arm. Place the arms on the outside of the frame

with the notches to the rear.

• Insert a tensioning chain through the hole shown and

attach the end link to the spring on the lower idler arm.

FIGure 35

5/16" x 3/4"
HEX BOLT (C)

5/16" NYLOCK
NUT (Y)

TENSIONING CHAIN (JJ)

5/16" WASHER (Q)

CaBLe oPeraTeD MaNuaL aTTaCHMeNT CLuTCH

FIGure 37

HEX BOLTS

DRIVE BELT

FLAT IDLER
PULLEY

(#46989)

STeP 37: (See FIGure 37)
• Two different length drive belts are included with

your snow thrower. Tractors with manual attachment
clutches and dual front deck suspension brackets use
the 55" drive belt with

#46989

printed on the outside

of the belt.

Do NoT uSe the other belt.

SToP

Did you choose the correct drive belt for
your tractor? Using the wrong length belt
may cause premature bearing or belt failure.

• Slightly loosen the hex bolt next to the flat idler pulley.

Install the drive belt down between the hex bolt and the
flat idler pulley with the flat side of the belt against the
pulley. Retighten the hex bolt.

• Loop the belt around the large v-pulley, placing it

between the v-pulley and the hex bolt next to the pulley.

«
...
15
16
17
18
19
...
»

Summary of Contents for LST42C





































Reviews:

No comments

Related manuals for LST42C

Brand: SNOWJOE Pages: 16

Brand: Walker Pages: 32

Brand: Honda Pages: 32

Brand: Honda Pages: 41

Brand: Honda Pages: 50

Brand: Honda Pages: 24

Brand: Mahindra Pages: 28

Brand: Troy-Bilt Pages: 28

Brand: Cub Cadet Pages: 30

Brand: Rammy Pages: 3

Single-Stage Snow Thrower

Brand: White Outdoor Pages: 20

Brand: Toro Pages: 2

Brand: Toro Pages: 20

Brand: Toro Pages: 20

Brand: Toro Pages: 28

Brand: Toro Pages: 32

Brand: Toro Pages: 12

1800 Power Curve

Brand: Toro Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands