Agri-Fab LST42C Owner'S Manual Download | Manualshive

Page: 10 / 36

background image

10

PIVOT LOCK PIN (GG)
(use this hole)

SHOULDER
BOLT (M)

L.H. HANGER
BRACKET

1/8" HAIRPIN
COTTER (EE)

NYLON TIE (II)

MOWER
CLUTCH
CABLE

FIGure 12

VIeweD FroM LeFT SIDe

STeP 13: (See FIGure 13)
• Assemble the drive belt onto the engine pulley first

and then onto the large pulley on top of the clutch/

idler assembly. The belt must be placed inside the
engine pulley belt keeper(s) and between the large
pulley and the keeper bolt next to it.

IMPorTaNT:

Do Not assemble the "V" belt outside of

the engine pulley keepers or outside of the keeper bolt

next to the large pulley.

•

Go to step 48 on page 21.

FIGure 13

VIeweD FroM uNDerNeaTH

ENGINE
PULLEY

ENGINE
PULLEY

Left Side
of Tractor

ENGINE
PULLEY
KEEPER

ENGINE
PULLEY
KEEPER

KEEPER BOLT

IDLER
PULLEY

CLuTCH/IDLer aSSeMBLY

FIGure 11

5/64" HAIR
COTTER PIN

SPACER

1/4" WASHER

TRACTOR'S
CLUTCH CABLE

CABLE
BRACKET

GROOVE

5/64" HAIR
COTTER PIN (DD)

1/4" WASHER (P)

SPACER (LL)

TRACTOR'S
CLUTCH CABLE

CABLE
BRACKET

5/64" HAIR
COTTER PIN (DD)

aTTaCH CLuTCH IDLer aSSeMBLY To TraCTor

STeP 12: (See FIGure 12)
• Attach the clutch/idler assembly to the tractor frame.

Hook the notched suspension arms onto the two
shoulder bolts (M) assembled to the outside of the
tractor frame. Lift the front of the assembly and attach
it to the R.H. and L.H. hanger brackets using two pivot
lock pins (GG) and 1/8" hairpin cotters (EE).

• Loosely attach the mower clutch cable to the left side

of the tractor frame with a nylon tie (II).

Do not

pull

the nylon tie completely tight. The cable may need to
be removed from the nylon tie when using the mower
deck.

STeP 11: (See FIGure 11)
• Find the cable clip that is attached to the left side

of the tractor frame underneath the footrest. Open
the clip and remove the mower clutch cable.

Do not

remove the clip from the tractor frame. The cable
reattaches to the clip when using the mower deck.

• Move the attachment clutch lever on the dash panel to

the disengaged position.

• Place the clutch/idler assembly on the floor on the left

side of the tractor.

• Attach the tractor's mower clutch cable to the cable

bracket on the clutch/idler assembly. Secure the cable
housing guide (groove down) to the cable bracket

using the original collar and a 5/64" hair cotter pin (DD).

• Place a spacer (LL) on the welded pin on the idler

arm. Hook the end of the clutch cable spring over the

pin and secure it with a 1/4" washer (P) and a 5/64"
hair cotter pin (DD).

• Align cable bracket with welded pin and tighten the

nut assembled in step 9.

«
...
8
9
10
11
12
...
»

Summary of Contents for LST42C





































Reviews:

No comments

Related manuals for LST42C

Brand: Ryobi Pages: 40

Craftsman 944.525410

Brand: Sears Pages: 48

Brand: Meec tools Pages: 36

Brand: Troy-Bilt Pages: 2

Brand: Land Pride Pages: 10

BERCO PIONEER 700455

Brand: Bercomac Pages: 34

Brand: Simplicity Pages: 8

Brand: Gude Pages: 4

Brand: Sheyenne tooling & Mfg Pages: 62

Brand: Meec tools Pages: 30

Brand: LGP Pages: 25

Great White M8000MD

Brand: Alamo Industrial Pages: 86

Brand: Ariens Pages: 16

Brand: Ariens Pages: 16

Brand: Ariens Pages: 4

Brand: Ariens Pages: 20

Brand: Ariens Pages: 12

Brand: Ariens Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands