manualshive.com logo in svg

AGL GradeLight 3000, Owner'S Manual

Share
Download
AGL GradeLight 3000 Owner'S Manual Download Page 35

34

SET

After a change, check the laser LCD and wait until SET 
appears again on the screen, and move the beam again if 
needed.

To save the calibration (beam position), press the 

Lock

button on the Remote (or the 

ENT

button on the laser 

keypad).

If it is not desired to save changes, turn the laser off.

To leave the CALIBRATION mode, move the cursor to 

EXIT

and press 

ENT

.

(If using the Remote, move up the menu using the Center 
Line button and move down the menu using the Standby 
(ZZZ) button.  Press the Lock button instead of ENT.)

To leave the SET UP mode, move the cursor to 

EXIT

and 

press 

ENT

(or LOCK on the Remote).

Final Calibration Check

Re-check the new calibration using the steps shown in the previous section with Stakes A 
and B.  If the marks are no more than 1/8 inch apart at 100 feet (at 30 m, no more that 3 mm 
apart), the laser is within the accuracy spec and calibrated correctly.

Summary of Contents for GradeLight 3000









































Reviews:

No comments

Brands by name

Popular brands

Load more brands