background image

2

GENERAL INFORMATION

The GradeLight pipe laser provides alignment and grade for installation of gravity flow 
sanitary and storm sewer pipelines, as well as for pipe jacking and tunneling.

The GradeLight includes:

·

Infrared remote control

·

Adjustable leg set for multiple pipe sizes

·

Rechargeable Li-Ion battery pack and spare alkaline battery compartment

·

OPTIONAL: Remote Receiver

Other features include a wide automatic self-leveling range, short length to fit tight inverts, 
and adjustable target with magnetic base (included in designated packages).

Specifications
GradeLight 3000

Self-Leveling Range

+45% to -15%

Grade Range

+40% to -10%

Grade Entry

Rolling counter or digit select

Grade Display

0.001%

Azimuth Range

20 ft. at 100 ft. (6m at 30m) 

Accuracy

±

1/16” at 100 ft. 

(

±

5mm at 100m; 

±

10 arc sec.; 

±

.005% ) 

Cross Axis Leveling

Automatic leveling ± 6 degrees

Beam Type/Output

Visible laser diode, 635nm, < 5mW, Class 3R

Environmental

IP68; nitrogen purged

Power Supply

1) Rechargeable lithium ion battery pack
2) 110/230V converter (charge and run simultaneously)
3) Spare battery compartment for 4 D-cell alkaline batteries
4) Optional 12V power  cord

Battery Life

40 hrs. Li-ion battery; 50 hrs. alkaline 

Charging Time

5 hrs. maximum

Mounting

5/8 x 11 (female mounting thread)

Operating Temperature

-4

°

to 122

°

F (-20

°

to +50

°

C) 

Storage Temperature

-40

°

to 140

°

F (-40

°

to +60

°

C)

Dimensions

Diameter: 5.5” (140 cm) / Length:<10.5“ (265mm)

Weight

7.6 lbs (3.5 kg) with alkaline battery

Warranty

1 year (2 and 3 Year Optional Warranties Available)

Remote 

Operating Range

600’ (190m) front (through the pipe); 25’ (7.6m) from rear 

Batteries

3 AA alkaline

Battery Life

2,000 hrs (1 year) 

Dimensions

4.7” x 2.35” x 1.2” (119 x 60 x 30mm)

Summary of Contents for GradeLight 3000









































Reviews: