Agilent Technologies varian 320-MS LC/MS Pre-Installation Instructions Download Page 14

9300025700: Rev. A 

14

 

of 14

  

Pre-installation Instructions 

 

Varian will not accept liability for damage if obviously received damaged materials were 
received without noting the damage on the receiving documents. 

;

 

Check the checklist box: Shipping cartons inspected for damage. If there was 

any damage, the conditions were reported.

 

Unpacking and Installing 

The Varian Representative will review the Pre-installation Checklist with the customer to ensure 
that the site requirements were met. The Varian Representative will unpack and install the 
instrument and demonstrate the fundamental operation and maintenance procedures. The User 
Representative must be present during the installation.  

The Varian Representative will demonstrate that the system meets the performance 
specifications, which are on the data sheet and any additional criteria explicitly written into the 
sales contract. 

Plan to analyze samples only after the installation is complete and the conditions of delivery 
accepted. The process requires at least three days.  

Spare Parts 

Please refer to the 

Quadrupole Hardware Manual, 

which has list of spare parts for routine 

operation. 

Preventive Maintenance 

The customer is responsible for performing routine and preventive maintenance of the LC, 
autosampler, MS, and data system. If using a nitrogen generator, perform the preventive 
maintenance to ensure that the nitrogen supply is clean and dry. Any instrument problems 
resulting from a contaminated gas supply are billable and not included in the Varian Warranty. 

Perform regular preventive maintenance to increase the life of the system, to maximize system 
uptime, and to optimize system performance. Please refer to the 

Quadrupole Hardware Manual 

for details. The Varian Representative will describe and demonstrate these procedures during 
the installation. 

Trademark Acknowledgment 

Microsoft® and Windows® are registered trademarks of Microsoft Corporation. PEEK™ is a 
registered trademark of the Victrex PLC Company, Lancashire, England. Other brand and 
product names are trademarks or registered trademarks of their respective holders.

 

 

Summary of Contents for varian 320-MS LC/MS















Reviews: