manualshive.com logo in svg

Agilent Technologies E8362A PNA Series, Installation Notes

Share
Download
Agilent Technologies E8362A PNA Series Installation Notes Download Page 4

4

  

                                                                                                                            

  

Installation Note E8362-90016

Items Included in the Upgrade Kit

Check the contents of your kit against the following list. If any item is missing or damaged, 
contact Agilent Technologies. Refer to 

“Contacting Agilent” on page 3

.

Table 1

Option 041 Upgrade Kit (E8362-60105) to Extend the E8362A to 40 GHz

Ref.

Desig.

Description

Qty

 Part Number

Parts for ALL analyzers with Option 014 (with or without any other options)

N/A

Installation note (this document)

1

E8362-90016

N/A

License key certificate

1

5964-5136

N/A

Model number nameplate (for 40 GHz analyzer, E8363A)

1

E8363-80001

A21

SOMA 50

1

5087-7130

A23

Channel R1 detector

2

5087-7133

A24

Channel R2 detector

A25

Test port 1 coupler

2

5087-7518

A26

Test port 2 coupler

A27

Channel A first converter (mixer)

2

5087-7122

A30

Channel B first converter (mixer)

N/A

Machine screw M3.0 x 18 (for attaching A23 and A24 detectors)

4

0515-0666

N/A

Machine screw M3.0 x 30 (for attaching SOMA 50)

4

0515-1349

N/A

Ribbon cable, A21 SOMA 50 to A16 test set motherboard

1

8121-0818

N/A

Cable, wrapped wire, detectors to A16 test set motherboard

2

E7340-60075

N/A

Test set deck front panel

1

E8364-00014

W1

A12 source 20 to A21 SOMA 50

1

E8364-20036

W2

A21 SOMA 50 to A22 switch/splitter

1

E8364-20034

W3

A22 switch/splitter to A23 channel R1 detector

1

E8364-20023

W4

A22 switch/splitter to A24 channel R2 detector

1

E8364-20024

W37

A23 channel R1 detector to A16 test set motherboard J204

1

E8364-60121

W38

A24 channel R2 detector to A16 test set motherboard J205

1

E8364-60122

W39

A21 SOMA 50 to A16 test set motherboard J206

1

E8364-60123

W65

A23 channel R1 detector to REFERENCE 1 SOURCE OUT

1

E8364-20047

W66

A24 channel R2 detector to REFERENCE 2 SOURCE OUT

1

E8364-20048

W67

A25 test port 1 coupler to PORT 1 CPLR ARM

1

E8364-20043

W68

A26 test port 2 coupler to PORT 2 CPLR ARM

1

E8364-20044

W69

PORT 1 RCVR A IN to A27 channel A mixer

1

E8364-20045

W72

PORT 2 RCVR B IN to A30 channel B mixer

1

E8364-20046

W60

Front-panel jumper

6

E8364-20059

Summary of Contents for E8362A PNA Series

































Reviews:

No comments

Brands by name

Popular brands

Load more brands