Agilent Technologies DSO80204B Service Manual Download Page 150

Page: 150 / 161

149

Theory of Operation

This

Service Guide

supports troubleshooting the Agilent Technologies oscilloscopes to

assembly level. Theory of operation is included only as supplemental information. It is
not comprehensive enough for component-level troubleshooting.

Block-Level Theory

The front panel provides:

• Dedicated knobs and pushbuttons for major oscilloscope functions.

• An 8.4-inch (diagonal) color flat panel display for waveform, measurement, and graphical

interface display.

• A front panel USB 2.0 port.

• Precision BNC connectors for channel input signals.

• BNC connector for auxiliary output signal.

• AutoProbe interface for probe power and probe control.

• A connection for probe compensation.

The rear panel provides several connections:

• The line power input.

• An GPIB connector, for connection to an oscilloscope controller.

• An RS-232 connection.

• A parallel printer connection.

• XGA monitor connection.

• Mouse and keyboard connections.

• LAN 10/100 connection.

• Auxiliary Trigger Input BNC.

• 10 MHz Reference Output BNC.

• 10 MHz Reference Input BNC.

• TTL trigger output BNC.

• Rear panel USB 2.0 ports.

The oscilloscope consists of several assemblies. Refer to the oscilloscope block diagram on the
previous page for the following discussion.

Summary of Contents for DSO80204B

































































































































































Search results

Summary of Contents for DSO80204B

Reviews:

Related manuals for DSO80204B

Brands by name

Popular brands

Agilent Technologies DSO80204B, Service Manual

Search results

Summary of Contents for DSO80204B

Reviews:

Related manuals for DSO80204B

Brands by name

Popular brands