Agilent Technologies DSO80204B Service Manual Download Page 106

Page: 106 / 161

Chapter 6: Replacing Assemblies

To remove and replace the covers

105

Carefully slide the bottom cover off the frame while spreading the top sleeve open as
shown.

Turn the instrument over and carefully slide the top sleeve off of the frame.

To replace the covers, reverse the above procedure.

Be sure to keep ribbon cables out of the way when replacing the covers, particularly the flex
cable and connector for the AutoProbe assembly at the bottom front of the oscilloscope.

C A U T I O N

PROPERLY TIGHTEN HANDLE AND SCREWS!
Tighten the side handle screws to 2.4 Nm (21 in-lbs) and rear feet screws to 2 Nm (18 in-lbs).

Figure 6-2

Remove bottom cover

Summary of Contents for DSO80204B

































































































































































Search results

Summary of Contents for DSO80204B

Reviews:

Related manuals for DSO80204B

Brands by name

Popular brands

Agilent Technologies DSO80204B, Service Manual

Search results

Summary of Contents for DSO80204B

Reviews:

Related manuals for DSO80204B

Brands by name

Popular brands