manualshive.com logo in svg

Agilent Technologies 708-DS, Operator'S Manual

Share
Download
Agilent Technologies 708-DS Operator'S Manual Download Page 97

Operating the 708-DS / 709-DS

4

708-DS / 709-DS Operator’s Manual

97

 

Numeric and Time / Date Entry

This screen is a specialized subset of the alphanumeric data entry 
screen. It has been optimized for numeric, date, and time data entry. As 
keys are pressed, they display in the upper box of the display. The valid 
data entry range and the previous data entry will be shown just below 
the display. The maximum valid data string length is 25 characters. 
Special function keys are defined below:

From the Numeric and Time / Date Entry screen:

•

Press 

Ok 

to return to the previous window. The data entered is 

returned and placed in the appropriate data entry box.

Table 13

Numeric and Time / Date Entry

Option

Function

Backspaces and deletes one character every time it is pressed.

/

Used as separator in date entries.

:

Used as separator in time entries.

AM

Designates morning when entering time in 12-hr format.

PM

Designates afternoon when entering time in 12-hr format.

Summary of Contents for 708-DS













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands