manualshive.com logo in svg

Agilent Technologies 708-DS, Operator'S Manual

Share
Download
Agilent Technologies 708-DS Operator'S Manual Download Page 80

80

708-DS / 709-DS Operator’s Manual

4

Operating the 708-DS / 709-DS

 

Menu Screen - Alarms

Two different alarms are available through the Alarms screen:

Table 5

Menu Screen - Alarms

Alarm

Function

Timer

This alarm functions as a countdown timer. Enter the duration as 
HH:MM:SS. Press 

Ok

 to start the timer. When the alarm duration 

expires, the Alarm Time Expired warning displays (

“Alarm Time 

Expired”

on page 106) and an audible alarm sounds. This alarm sounds 

until you press

 Ok

. To cancel a previously running alarm before time 

has expired, enter 0 for the Timer Alarm value.

Pause Duration

This field allows you to set the maximum pause period while running a 
method. When a running method is paused, a timer starts. If the pause 
time exceeds this Pause Duration, the Pause Duration Exceeded error 
displays (

“Pause Duration Exceeded”

on page 110), an alarm sounds, 

and a message is sent to the printer. Entering a zero in this field disables 
the Pause Duration Alarm.

Summary of Contents for 708-DS













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands