manualshive.com logo in svg

Agilent Technologies 08757-60159, Installation Note

Share
Download
Agilent Technologies 08757-60159 Installation Note Download Page 45

08757-90195

45

Step 18.    Operator’s Check

After upgrading your instrument, complete the following test to verify its performance.

1. Turn the power on.

2. Perform the Operator’s Check. Refer to the Operating Reference 8757D Scalar Network 

Analyzer (08757-90169) on page A-1. The Operator’s Reference is part of the Operating 
Manual (08757-90109).

Step 19.    Troubleshooting

If there is a possibility that the log amplifier boards (white guides) were not replaced in their 
original positions, perform the following procedures. 

1. Perform the Calibration Check Procedure. Refer to the Operating and Service Manual for 

the 11613B Calibrator (11613-90011). Follow the procedure given for the 8757A in
Chapter 3.

2. If the Calibration Check Procedure fails, perform the Calibration Procedure. Refer to the 

Operating and Service Manual for the 11613B Calibrator (11613-90011). Follow the 
procedure given for the 8757A in Chapter 3.

Summary of Contents for 08757-60159















































Reviews:

No comments

Brands by name

Popular brands

Load more brands