manualshive.com logo in svg

AGI MK/HX 10-36, Assembly & Operators Manual

Share
Download
AGI MK/HX 10-36 Assembly & Operators Manual Download Page 14

14

30549 R1

Table 1

Safety Decals (continued)

Part Number

Description

20807

To prevent serious injury or death:

• Read and understand the manual before 

assembling, operating, or maintaining the 

equipment.

• Only trained personnel may assemble, operate, 

or maintain the equipment.

• Children and untrained personnel must be kept 

outside of the work area.

• Do not modify the equipment. Keep in good 

working order.

• If the manual, guards, or decals are missing or 

damaged, contact factory or representative for 

free replacements.

• Lock out power before performing maintenance.
•  To prevent equipment collapse or upending, 

support equipment tube while disassembling 

certain components.

• Follow grain storage structure manufacturer's 

warnings when loading and unloading.

• Electric motors must be grounded. Disconnect 

power before resetting overloads.

WARNING

2. SAFETY FIRST

MK/HX 10-36 – SWING-AWAY GRAIN AUGER

Summary of Contents for MK/HX 10-36























































Reviews:

No comments

Brands by name

Popular brands

Load more brands