AGA GATEMASTER 900 HD Installation Manual Download Page 4 | Manualshive

Page: 4 / 23

AGA GATEMASTER 900 HD Installation Manual Download Page 4

4

THE AGA GATEMASTER 900 AUTOMATIC SWING GATE SYSTEM

Product Description and Applications

This system is for residential or light commercial automation of a swinging gate.

Technical Specifications:

Motor: 24V DC motor with mechanical release
Gear type: worm gear
Max absorbed power: 144W
Peak thrust: 3500N
Nominal thrust: 3000N
Duty cycle: 20%
Stroke length: 12 inches
Power supply: 110V AC converted to 24V DC with built in transformer
Nominal input power: 2A
Maximum operating current: 5.5A for maximum 10 seconds
Maximum gate weight: 500 lbs
Maximum gate length: 14 feet
Control Panel Voltage: 24V AC, available for 24V DC backup battery
Suitable for single or dual swing gate opener
Radio Controls: 433 MHz customized rolling code
Support remote control: Can memorize 120 transmitters at most
Actuators: 24V DC Actuator x2

This diagram shows a typical installation including some optional accessories:

«
...
2
3
4
5
6
...
»

Summary of Contents for GATEMASTER 900 HD
























Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands