manualshive.com logo in svg

Afar NX-2E1, Operator'S Manual

Share
Download
Afar NX-2E1 Operator'S Manual Download Page 61

NetCrossing Gateway NX-2E1/T1 Operator’s Manual

A-1

APPENDIX A – Command Summary

This appendix lists all commands organized in the respective functional groups.  Parameters that are
part of the gateway configuration are identified by having an entry under the “Factory Configuration”
heading.   When entering a command, if a parameter that is part of the gateway configuration is
omitted, the value for that parameter is not modified.

For commands that are not part of the gateway configuration, if a parameter is omitted, the value for
that parameter defaults to the value indicated in bold.

Configuration Management Commands

Command

Parameters

Values

change-password

enable-configuration

<string>

display-configuration

source

current

main
alternate
basic
factory

load-configuration

source

main

alternate
basic
factory

lock

save-configuration

destination

main

alternate

unlock

enable-configuration

<string>

Summary of Contents for NX-2E1












































































Reviews:

No comments

Brands by name

Popular brands

Load more brands