manualshive.com logo in svg

Afar NX-2E1, Operator'S Manual

Share
Download
Afar NX-2E1 Operator'S Manual Download Page 55

NetCrossing Gateway NX-2E1/T1 Operator’s Manual

4-21

history

Displays the previous commands entered.

license

key=< ASCII string>

The “license” command is used to turn ON or OFF a set of optional features or capabilities. The
key is a 35-character string combination of ASCII letters, numbers, and hyphens.  The key must
be input with the syntax as shown in the example below, including hyphens, for the gateway to
accept it.  The characters can be input as upper or lower case.

After entering the key you must reboot the gateway for the feature, enabled by the key, to take
effect.

Each key is unique for a particular gateway serial number and capability, i.e. a key generated to
turn ON a capability on one serial number will not work on another gateway.

Example:

>

license key=02EL1-ZGZ42-G0000-00C54-81WAJ-C9BEK

logout

Closes the current Econsole session.

reboot

Resets the gateway causing the software to perform a complete start up sequence.  This is
equivalent to power cycling the gateway off and on.

time

time=hh:mm:ss
date=day-month-year
zone=zone-code or offset

This command is identical to the “date” command explained above except for the order of the
parameters.  It allows the time and date to be entered as:

> time 10:32:06  16-may-2000

version

Displays the gateway model and software version.

Summary of Contents for NX-2E1












































































Reviews:

No comments

Brands by name

Popular brands

Load more brands