manualshive.com logo in svg

Afar NX-2E1, Operator'S Manual

Share
Download
Afar NX-2E1 Operator'S Manual Download Page 26

NetCrossing Gateway NX-2E1/T1 Operator’s Manual

2-8

2.4

 

Synchronization Port

The SYNC connector is used to propagate radio synchronization information between co-located
gateways.  This feature is only applicable when you use the NetCrossing Gateway in conjunction with
AFAR radios.

In a network consisting of Afar radios and gateways, synchronization information flows between all
units through (i) RF links, (ii) Ethernet messages, and/or (iii) the SYNC connector of the gateways.
This synchronization mechanism allows deploying a large network where all radios have their TDD
cycles synchronized, eliminating self-generated interference between co-located radios.

When you co-locate multiple radios with each one connected to a gateway, you should daisy-chain
the SYNC signal between all gateways.  Then use the 

tdd

 command to set the 

synch-mode

 of all the

co-located gateways to either 

auto

 or 

master

.  In any large network only one site should be the

source of the timing.  Set the 

synch-mode

 to 

master

 only at that site.  The master gateways will “co-

share” the timing such that, even if one gateway fails, the synchronization information continues to
flow. This synchronization feature is explained in detail in the radio manual.

Summary of Contents for NX-2E1












































































Reviews:

No comments

Brands by name

Popular brands

Load more brands