manualshive.com logo in svg

Afar NX-2E1, Operator'S Manual

Share
Download
Afar NX-2E1 Operator'S Manual Download Page 49

NetCrossing Gateway NX-2E1/T1 Operator’s Manual

4-15

•

 

If the Gateway is connected to an Afar radio, displays the radio synchronization status and
how much throughput is available for LAN traffic.

The statistics shown in this table (maximum jitter, number of errors, last error) can be cleared
by specifying the clear=1 parameter.

gateways table

This table lists all the gateways that are reachable in the WAN network, several of their
configuration parameters and whether they are compatible to establish a serial link with this
unit.  The first entry is always for the unit itself.

ethernet table

This table can be displayed in two formats, “counts” (default) and “times”.

>show  ethernet

Ethernet Stations:
                                               --Discard--      --Forward--
 #       MAC address   IP address     Port     from       to     from       to
 0 ff-ff-ff-ff-ff-ff                  Bcast     0         0        0      183
 1 00-d0-39-00-2d-cb                   me       0         0      209      165
 2 00-a0-cc-66-8e-a6   207.154.90.171 Local   136        54   139575      172
 3 00-d0-39-00-2d-c3                   WAN      0         0        0        0

>show  ethernet times

Ethernet Stations:
 #       MAC address   IP address     Port  MC  Time added      Idle
 0 ff-ff-ff-ff-ff-ff                  BCast   29-Nov 16:17:08
 1 00-d0-39-00-2d-cb                   me     29-Nov 16:17:08   0.01
 2 00-a0-cc-66-8e-a6   207.154.90.171 Local   29-Nov 16:17:15   0.00
 3 00-d0-39-00-2d-c3                   WAN    29-Nov 16:23:41   9.18

Both formats list all the ethernet stations attached to either port.  The tables list the MAC
(Ethernet) address of the station, and, if known, the IP address.

The first entry in the table tracks broadcast traffic while the second entry is always the address
of the gateway itself.  The “Port” column shows the port where that address was last seen.

The “counts” format shows the cumulative number of ethernet packets that have been seen with
that MAC addresses in the “source” (from) or the “destination” (to) fields.  In bridge mode the
gateways are in “promiscuous” mode and look at all the ethernet packets in both networks.  The
gateways “discard” the packets that are known to be local, but “forward” all other packets to
the opposite network.  These are accounted separately in the report.

The “times” format indicates whether that entry is for a “multicast” (MC) address, shows the
time when the station was added to the table, and how long since that address has been seen.
When the “idle” time exceeds the time specified by the “bridge” command, that entry is deleted
from the table.

Summary of Contents for NX-2E1












































































Reviews:

No comments

Brands by name

Popular brands

Load more brands