AES uScope Getting Started Download Page 1 | Manualshive

Page: 1 / 12

AES uScope Getting Started Download Page 1

AES uScope Manual

www.AESwave.com

Copyright 2011 by Automotive Electronics Services, Inc.

Page 1

The uScope

– Getting started

Introduction

(fw 4.19 October 1, 2011)

The uScope! A single channel, pocket-sized,
digital storage oscilloscope that ¡s small, quick,
and powerful. Automotive presets get you going
quickly. Ideal for the Flat Rater that wants the
ultimate run and gun lab scope for pin point
testing. Ideal for the student that is ready to
start scope'n.

The uScope is powered by an easy to use
interface enhanced with automotive presets and
reference waveforms.

Put the power of the uScope in your hand (and shirt

pocket).

Secondary ignition, injectors, mass air flow, crank,
cam, TPS, 02, CTS you name it it'll scope it. The
uScope is also perfect for your low amp probe,
secondary ignition pickup and pressure transducers.

When you just need to run a quick
test to verify the "signal" is working
as the engineer intended, why spend
time pulling out and setting up your
"big boy Scope" when you can do it
faster with the uScope?

1
2
3
...
»

Summary of Contents for uScope













Reviews:

No comments