background image

40

10. Warranty and returns

10.1 Warranty

LIMITED WARRANTY

Thank you for purchasing a heat pump from us.

This warranty covers manufacturing and material defects in all components for a period of two years after the

date of purchase.

This warranty is limited to the original purchaser in the retail sector. It is not transferable, and it is not

applicable to products that have been removed from their original installation location. The liability of the

manufacturer is limited to the repair or replacement of defective components and does not include the cost of

labour for removing and replacing the defective component(s), the cost of transporting component(s) from or

to the factory, or costs associated with other materials necessary for carrying out repairs. This warranty does

not cover any defects attributable to the following causes:

1.

Installation, operation or maintenance of the product other than in accordance with the guidelines

and/or instructions in the Installation and Operation Manual supplied with the product.

2.

Faulty or deficient work performed on the product by an installer.

3.

Failure to maintain the correct chemical balance in the swimming pool

[pH between 7.0 and 7.8; total

alkalinity (TA) between 80 and 150 ppm; free chlorine concentration between 0.5 and 1.2 mg/l; total

dissolved solids (TDS) less than 1,200 ppm; maximum salt concentration 8 g/l]

.

4.

Improper use, modification, accident, fire, flood, lighting strike, rodents, insects, negligence, neglect,

or force majeure.

5.

Deposits, freezing, or other conditions that impair proper water flow through the product.

6.

Operating the product with a flow rate outside the published minimum and maximum specifications.

7.

Use of components or accessories not designed or made for this product.

8.

Chemical contamination of the air used by the product or improper use of decontaminating chemicals,

such as the addition of decontaminating chemicals through the skimmer or in the pipes or lines located

upstream of the heat pump and the cleaning hose.

9.

Overheating, improper electrical connections, improper power supply, secondary damage attributable

to defective O-rings, diatomaceous filters or filter cartridges, or damage caused by putting the pump into

operation in the absence of sufficient water.

LIMITATIONS ON LIABILITY

This is the sole warranty provided by the manufacturer. Nobody is authorised to grant other warranties in our

name.

THIS WARRANTY REPLACES ALL OTHER EXPLICITLY GRANTED OR IMPLICIT WARRANTIES, INCLUDING BUT

NOT LIMITED TO ANY FORM OF IMPLICIT WARRANTY OF SUITABILITY FOR A PARTICULAR PURPOSE OR

FITNESS FOR SALE. WE EXPLICITLY DISAVOW ANY LIABILITY FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL

LOSS OR DAMAGE OF A PUNITIVE NATURE RESULTING FROM THE VIOLATION OF AN EXPLICITLY GRANTED OR

IMPLICIT WARRANTY.

This warranty gives you specific legal rights, which may vary depending on the country.

WARRANTY CLAIMS

To ensure prompt handling of your warranty claim, please contact your dealer and provide the following

information to the dealer: proof of purchase, model number, serial number and date of installation. The

installer will contact the factory to obtain instructions regarding the procedure for making warranty claims and

to find out the location of the closest service centre.

All returned components must be marked with a

RMA number

so that it can be determined whether they are

covered by the warranty.

Summary of Contents for Hydro-Pro Inverter 07








































Reviews: