manualshive.com logo in svg

Aeroqual AQM 65, User Manual, Page: 45 / 127

Share
Download
Aeroqual AQM 65 User Manual Download Page 45

 

 

MRK-D-0034 V2.0 

 

 

 Aeroqual AQM 65 User Guide  

 

 

Page | 44 

3.4.2  Service and Calibration app 

The Service and Calibration app has three functions, Service mode initiation, changing gain and offset 
during calibration, and configuring and running the AirCal 8000. 

The Service and Calibration app can be accessed by all user types and all instrument licences. 

Service Mode button 

When a service engineer visits the AQM 65 to perform routine service such as filer changes or flow 
checks, this can cause the data to read very high or very low. During service activities the AQM 65 
ca

n be put in to Service Mode by clicking the service mode button. This will tag the data as “service 

data” which can later be filtered when daily or hourly averages are being calculated.  

See Section 4.3.1for further discussion on Service Mode 

Gain and offset adjustment 

Gain and offset adjustments are made as part of the AQM 65 gas calibration procedure. These 
adjustments are made in the Service and Calibration App. 

AirCal 8000 

The AirCal8000 is an optional integrated calibration module. The module can be programmed to 
deliver gas from attached calibration cylinders. Gas can be delivered manually or a schedule can be 
set to deliver calibration gas automatically.  

 

 

Figure 3-14 The service and calibration app can be used to put the AQM in to service mode, adjust offset 
and gain settings and control the AirCal 8000 

 

 

Summary of Contents for AQM 65
































































































































Reviews:

No comments