Aeroqual AQM 65 User Manual Download

Page: 35 / 127

MRK-D-0034 V2.0

Aeroqual AQM 65 User Guide

Page | 34

3.1 Connecting to the AQM 65 for the first time

The AQM 65 ships from the Aeroqual factory as a WIFI access point. This means that when the AQM
65 is powered on, the AQM 65 will appear as an available WIFI network.



The name of the WIFI network (SSID) will be the serial number of the AQM 65.



The WIFI password is “Aeroqual”



You must connect successfully to this WIFI network to achieve connection to the AQM 65.

Figure 3-2 In WIFI access point mode the AQM 65 appears as a WIFI network in the lit of WIFI networks on
your PC.

The next step is to open a blank browser window and enter

10.10.0.1

in to the address bar.

Figure 3-3 The AQM 65 default access login, this should be removed after another admin account has
been created

The default login name is “

administrator

” The default password is “

aqmadmin

”

Summary of Contents for AQM 65
































































































































Search results

Summary of Contents for AQM 65

Reviews:

Related manuals for AQM 65

Brands by name

Popular brands

Aeroqual AQM 65, User Manual

Search results

Summary of Contents for AQM 65

Reviews:

Related manuals for AQM 65

Brands by name

Popular brands