background image

32 

© Aero-Stream, LLC 2022  

102822 Rev. H 

 Use the garbage can for items such as caustic soda, acids, copper sulfate, chemical cleaners, paint 

thinner, latex or oil based paint, solvents, waxes, polishes, pesticides, poisons, fuels, motor oil, 
hazardous wastes, filter tip cigarettes, sanitary napkins, all feminine products, paper towels, rags, 
plastic objects or disposable diapers.  All of these items cannot be broken down or are very difficult 
for the bacteria to break down. 

 Discharge your water softener and iron filter to another suitable location, i.e. not into the septic 

system, in accordance with your local codes and ordinances.  

 Route your rain downspouts away from the drain field, seepage pit or drywell. 

 Do not plant trees or shrubs above the drain field, seepage pit or drywell.  The roots of the plantings 

will grow into and plug the drain field, seepage pit and drywell. 

 Keep heavy vehicles off of the drain field, seepage pit or drywell.  The heavy vehicles not only 

compact the soils but also can crush the perforated laterals of the absorption component.  The 
compacted soil is less permeable than loose soil.  

 Do not dump recreational vehicle (RV) holding tank waste into your septic tank.  This produces a 

large surge of sewage to the system and will most likely force untreated effluent out of the septic tank 
into the distribution component.  Also, most RV owners use some type of odor control chemicals that 
are harmful to the system.  These are usually blue liquids or tablets.  These odor control chemicals 
are disinfectants to kill the odor causing anaerobic bacteria in the waste.  When the disinfected waste 
from an RV system is dumped into the septic tank, it kills the bacteria in the system. 

 

 

Manufacturer’s Limited Warranty

 

 

 

DISCLAIMER, DURATION, AND SCOPE OF THIS WARRANTY

 

Aero-

Stream, LLC (“Aero”) warrants its NSF/ANSI 40 Aerobic Treatment Units against defective materials or workmanship at the time of 

shipment for a period of 24 months.  To make a valid claim under this warranty, Aero must be notified through writing, email or otherwise of any 
warranty claim within the applicable warranty period and in the manner described below.  

 

All implied warranties including the

 IMPLIED WARRANTY OF MERCHANTABILITY 

and

 

the

 IMPLIED WARRANTY OF FITNESS FOR A 

PARTICULAR PURPOSE 

are also 

LIMITED IN DURATION 

to the applicable warranty period.  

SOME STATES DO NOT ALLOW 

LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MIGHT NOT APPLY TO YOU.

  This 

warranty only covers the original Buyer of Aero’s product.   Aero will not be responsible under this warranty for any defect, failure, or 
malfunction of this product caused by abuse, misuse, unauthorized adjustments or dissembling of this product during the duration of this 
warranty.  

AERO MAKES NO OTHER WARRANTY BEYOND THAT CONTAINED IN THIS WRITING.  

 

EXCLUSIVE REMEDY AVAILABLE UNDER THIS WARRANTY

 

If after the expiration of the Customer Service Policy, the Aero product fails to operate properly under normal conditions within the remaining 
warranty period because of a defect in materials or workmanship, Aero will repair or replace this product without cost to you for parts or 
labor.  If repair or replacement of the product is impossible or impracticable, as an alternative, Aero retains the option to reimburse you with the 
original purchase price of the product within a reasonable amount of time.  

THE REMEDY DESCRIBED ABOVE SHALL BE YOUR 

EXCLUSIVE REMEDY FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY.  NO OTHER REMEDY FOR BREACH OF THIS 
WARRANTY, EXPRESS OR IMPLIED (INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 
PARTICULAR PURPOSE),

 

SHALL BE AVAILABLE TO YOU

. Under no circumstances will Aero be responsible for 

INCIDENTAL AND/OR 

CONSEQUENTIAL DAMAGES, 

lost profits, lost sales, injury to property, or any other loss.  These limitations do not apply, however, to 

damages related to personal injury. 

SOME STATES DO NOT ALLOW LIMITATIONS ON INCIDENTAL OR CONSEQUENTIAL DAMAGES, 

SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. 

  For service, questions or to make a warranty claim, contact Aero at W300 

N7706 Christine Lane, Hartland, Wisconsin, 53029, visit our website at www.aero-stream.com or email us at 

[email protected]

If Buyer is 

making a warranty claim, please provide a description of the nature of the problem.  Alternatively, call the following toll-free number to obtain 
further warranty instructions: 

1-877-254-7093

.  

STATE LAWS AND THIS WARRANTY

 

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM 
STATE TO STATE.

  To the extent that state law renders any provision in this warranty inoperative, state law shall apply and that 

clause shall be severed from the warranty; this severance, however, does not render the entire warranty inoperative.      

Summary of Contents for AS1000-2







































Reviews: