background image

APPENDIX A 

A-1 

 

APPENDIX A -  

WATER HEATER MENU ITEM DESCRIPTIONS 

 

MENU LEVEL & OPTION 

DESCRIPTION 

OPERATING MENU 

 

  

Active Setpoint 

This is the setpoint temperature to which the 

control is set when operating in the Constant 

Setpoint or Remote Setpoint Mode.  When in the 

Constant Setpoint Mode, this value is equal to the 

Internal Setpoint setting in the Configuration Menu.  

When in the Remote Setpoint Mode, this value is 

the setpoint equivalent to the remote analog signal 

supplied to the unit 

  Air Temp 

For monitoring purposes only 

  Outdoor Temp 

Displayed only if outdoor sensor is installed and 

enabled. 

  Valve Position In 

Desired input valve position.  This would normally 

be the same as the valve position shown on the 

bargraph when the heater is operating. 

  Flame Strength 

Displays flame strength from 0% to 100%. 

  Run Cycles 

Displays the total number of run cycles from 0 to 

999,999. 

  Run Hours 

Displays total run time of unit in hours from 0 to 

9,999,999. 

  Fault Log 

Displays information on the last 20 faults (0 – 19). 

SETUP MENU 

 

  Password 

Allows password to be entered.   

Once the valid password (159) is entered, options 

in the Setup, Configuration and Tuning Menus can 

be modified. 

  Language 

English only 

  Time 

Displays time from 12:00 am to 11:59 pm. 

  Date 

Displays dates from 01/01/00 to 12/31/99 

  Unit of Temp 

Permits selection of temperature displays in 

degrees Fahrenheit (°F) or degrees Celsius (°C).  

Default is °F. 

  Comm Address 

For RS-485 communications (0 to 127).  Default 

address is 0.  RS-232 should have its own 

(programmable) password. 

  Baud Rate 

Allows communications Baud Rate to be set (2400 

to 19.2K).  Default is 9600. 

  Software Version 

Identifies the current software version of the 

control box (Ver 0.0 to Ver 9.9). 

 

 

 

 

Summary of Contents for KC Series























































































































Reviews: