background image

ADVANCED ENGINE MANAGEMENT INC. 

2205 126

th

 Street Unit A, Hawthorne, CA. 90250 

Phone: (310) 484-2322 Fax: (310) 484-0152 

http://www.aemelectronics.com 

Instruction Part Number: 10-3350 Rev A 

 2013 Advanced Engine Management, Inc 

 

Page 1

 

 

 

 

Multi-Input Water/Methanol 

Injection Kit 

P/N 30-3350, 30-3351, 30-3352

 

 

 

 

This product is legal in California for racing vehicles only and should never be used 
upon a highway. This product is legal solely for vehicles used in competition which 
may never be used upon a public road or highway

 

 
 
 

 

WARNING:

 

!

 

Improper installation and/or adjustment of this product can result in 
major engine/vehicle damage! Use of this injection system requires 
proper tuning! Use this system with EXTREME caution! If you are 
uncomfortable with anything about this, please refer the installation to 
an AEM trained tuning shop or call 800-423-0046 for technical 
assistance. You should also visit the AEM Performance Electronics 
Forum at http://www.aempower.com 
 
NOTE: AEM holds no responsibility for any engine damage that 
results from the misuse of this product!

 

Summary of Contents for 30-3350
























Reviews: