background image

 

599 519 523 EN 

DGS-TDS 
21.04.08 

2.3  Alarm message "E“ 

 
When the appliance is switched on, "E“ / „xx“ Alarm Number is displayed in the timer display. With 
Frontline the display of the front zone indicates the error number when switching on. The affected 
zones are subsequently displayed with an "E" in the cooking phase display and are thereby disabled. 
The other zones can still be used. 
 
example (left touch control / right indication in the cooking zone): 
1) Display alarm number after switching on for 10 sec. 

 

E

Alarm number 

5

 

2) 2 zones are disabled. 

E

E

0

0

 

 

Alarm 
Symptom

 

Display in 
the 
Cooking 
Hob Timer

 

Possible Alarm 
Cause

 

Alarm Remedying

 

Alarm display in the 
Touch Control 
display. 

"E0“ 
 

Incorrect configuration on 
the Filterboard. 

Disconnect cooking hob from mains, 
wait 10 sec and reconnect the mains 
supply. 
Should alarm still be displayed, 
replace filterboard.. 

 

"E3“ 

Under voltage or over 
voltage, is only displayed 
for 10 sec. after voltage 
has been applied. 

1) Disconnect cooking hobs from the 
mains, wait 10 sec. and reconnect the 
mains. 
2) Should alarm still be displayed,  
test L1 against N (4),  
test L2 against N (5)  at the mains 
connection  

(1)

3) If OK, see  
See Chapter  3 Testing Power 
Component 
 
 

 

"E4“ 

Coil temperature sensor 
defect or not correctly 
connected. 

1) 

(5)

Inspecting the contacts on the 

power component. 
Is the connector inserted? 
2) The resistance at room 
temperature (25°C) amounts to 1000 
Ohm. This corresponds to approx. 3.3 
Ohm per +1°C deviation. 
If not in this range, replace affected 
coil including temperature sensor. 
3) Should above not succeed, replace 
power component concerned. 

Summary of Contents for 88101






















Reviews: