manualshive.com logo in svg

Advantech PCIE-1816, User Manual, Page: 29 / 62

Share
Download
Advantech PCIE-1816 User Manual Download Page 29

23

PCIE-1816_1816H User Manual

Chapter 3

S

ignal Connections

 

External AI Sample Clock

The external AI sample clock is useful when you want to pace acquisitions at rates
not available with the internal AI sample clock, or when you want to pace at uneven
intervals.  Connect  an  external  AI  sample  clock  to  screw  terminal  AI_CLK  on  the
screw  terminal  board.  Conversions  will  start  on  the  rising  edge  of  the  external  AI
sample clock input signal. You can use software to specify the clock source as exter-
nal. The sampling frequency is always limited to a maximum of 10 MHz for the exter-
nal AI sample clock input signal.

Figure 3.6 External Clock Source Connection

Trigger Sources Connections
External Digital (TTL) Trigger

For analog input operations, an external digital trigger event occurs when the PCIE-
1816/  1816H  detects  either  a  rising  or  falling  edge  on  the  External  AI  TTL  trigger
input signal from screw terminal DTRG0 and DTRG1 on the screw terminal board.
The trigger signal is TTL-compatible.

Figure 3.7 External Digital Trigger Source Connection

Summary of Contents for PCIE-1816































































Reviews:

No comments