manualshive.com logo in svg

Advantech MIC-3369C, User Manual

Share
Download
Advantech MIC-3369C User Manual Download Page 74

MIC-3369 User’s Manual

64

4.1.7 PNP/PCI Configuration Setup

This section describes configuring the PCI bus system. PCI, or Personal 
Computer Interconnect, is a system which allows I/O devices to operate 
at speeds nearing the speed the CPU itself uses when communicating 
with its own special components. This section covers some very technical 
items and it is strongly recommended that only experienced users should 
make any changes to the default settings.
 

Figure 4.11: PNP/PCI configuration screen

Reset Configuration Data

Normally, you leave this field Disabled. Select Enabled to reset Extended 
System Configuration Data (ESCD) when you exit Setup if you have 
installed a new add-on and the system reconfiguration has caused such a 
serious conflict that the operating system can not boot. The settings are: 
Enabled and Disabled (Default).

Resource Controlled By

The Award Plug and Play BIOS has the capacity to automatically config-
ure all of the boot and Plug and Play compatible devices. However, this 
capability means absolutely nothing unless you are using a Plug and Play 
operating system such as Windows® 95/98. If you set this field to "man-
ual" choose specific resources by going into each of the sub menu that 
follows this field (a sub menu is preceded by a "ÿ"). The settings are: 
Auto (ESCD) (Default), Manual.

IRQ Resources

Summary of Contents for MIC-3369C























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands