manualshive.com logo in svg

Advantech-DLoG TREK-572, User Manual

Share
Download
Advantech-DLoG TREK-572 User Manual Download Page 9

7

TREK-572/303 User Manual

 

 

 

 

 

Safety Precaution - Static Electricity

 

 

Follow these simple precautions to protect yourself from harm and the products from 
damage. 

„ 

To avoid electrical shock, always disconnect the power from your PC chassis 

before you work on it. Don't touch any components on the CPU card or other 
cards while the PC is on. 

„ 

Disconnect power before making any configuration changes. The sudden rush 

of power as you connect a jumper or install a card may damage sensitive elec- 
tronic components. 

 

Warning!  

1. 

Input voltage rated: 9 

~ 

32 Vdc.

 

2. 

Transport: carry the unit with both hands and handle with care.

 

3. 

Maintenance: to properly maintain and clean the surfaces, use only 

approved products or clean with a dry applicator.

 

 
 
 
 
 

 

 

European Contact Information:

 

 

Advantech Europe GmbH Kolberger Straße 7 
D-40599 Düsseldorf, Germany 
Tel: 49-211-97477350 
Fax: 49-211-97477300 

Summary of Contents for TREK-572











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands