Advantech-DLoG TREK-572 User Manual Download Page 8 | Manualshive

Page: 8 / 74

background image

TREK-572 /303 User Manual

6

only with same or equivalent type recommended by the manufacture. Discard
used batteries according to the manufacturers instructions.

17.

This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that

may cause undesired operation.

18.

CAUTION: Always completely disconnect the power cord from your chassis
whenever you work with the hardware. Do not make connections while the
power is on. Sensitive electronic components can be damaged by sudden
power surges.

19.

CAUTION: Always ground yourself to remove any static charge before touching
the motherboard, backplane, or add-on cards. Modern electronic devices are
very sensitive to static electric charges. As a safety precaution, use a grounding
wrist strap at all times. Place all electronic components on a static-dissipative
surface or in a static-shielded bag when they are not in the chassis.

20.

CAUTION: Any unverified component could cause unexpected damage. To
ensure the correct installation, please always use the components (ex. screws)
provided with the accessory box.

21.

«
...
6
7
8
9
10
...
»

Summary of Contents for TREK-572











































































Reviews:

No comments

Related manuals for TREK-572

PC 300GL Type 6267

Brand: IBM Pages: 58

FlexControl 1883

Brand: Gardena Pages: 19

Brand: Antec Pages: 10

Brand: Walfront Pages: 39

PC 300GL Type 6561

Brand: IBM Pages: 66

Brand: DFI Pages: 15

Brand: Gateway Pages: 346

Brand: Altair Pages: 35

Brand: HP Pages: 66

Brand: HP Pages: 28

Brand: XtendLan Pages: 65

PCV-RZ14G Online Help Center (VAIO User Guide)

Brand: Sony Pages: 1

Brand: Sony Pages: 2

PCV-RXA842 Online Help Center (VAIO User Guide)

Brand: Sony Pages: 1

PCV-RX820 Online Help Center (primary )

Brand: Sony Pages: 1

Brand: Sony Pages: 1

PCV-RX770 Computer User Guide (primary manual)

Brand: Sony Pages: 1

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands